How to Install a Backup Camera in Your Car?

A backup camera, also known as a reversing or rear-view camera is made solely for the back of a vehicle to assist in backing up and reduce the rear blind spot. The best backup camera is mainly built to avoid a backup crash. Rear view cameras are now a standard feature on the latest cars because it adds more safety and ease while reversing.

Although, there are lots of aftermarket brands camera available for vehicles, not so many people understand how to install a backup camera in their cars when they eventually buy one. In this piece, I will be going through the step-by-step procedures involved in installing a backup camera in your car.

STEP 1 — REMOVE YOUR LICENSE PLATE:

With the aid of a screwdriver, you can remove your license plate by unscrewing all the fastening screws holding it in place, and then pull the plate off and keep it in a safe place. Then drill a hole either in the place number or the bumper.

STEP 2 — PUT THE CAMERA ON THE VEHICLE AND LAY THE CABLES:

It is essential that you set the camera before attempting to lay the sure at all. Mount your camera and run the wires through the hole dug to the monitor at the dashboard of the vehicle. The most straightforward means is to channel the cables through the kick panels and the routes close to the door. Immediately you have done this; the wiring can be through the rubber grommet at the channel’s end.

STEP 3 — LINK THE CAMERA’S CORD TO THE POWER SUPPLY:

How you go about this depends on the configuration of the camera. If it is wireless, this step might not be required. Also, the construction of the car can as well determine how to configure the camera. From the rear of the bumper, the cords can be linked to the camera to power it with the reverse light supply. The wiring can be set with a crimper, a handy tool.

STEP 4- LINK THE DISPLAY SCREEN TO YOUR CAR:

Irrespective of the connection type of the camera, it is essential that the screen of the backup camera is connected to the accessory output to turn on the reverse light anytime the car is on the reverse. After that, the monitor should be either coupled to the front panel or windshield. To ease the connection, a suction cup can be used. Power for the controls can be sourced by plugging the cord end into the cigarette lighter.

STEP 5- CONNECT THE MONITOR OF THE CAMERA TO THE DISPLAY SCREEN:

Wireless back up cameras don’t require this step. To connect the camera to the viewing screen of the car takes a proper understanding of the vehicle as well as the camera in question. You can start by passing the cord through the frame of the back seat on the right side. Immediately the wire gets into the car, pass it below the kick panel along the front seat to the dash close to the A-pillar.

STEP 6 — LINK THE DISPLAY SCREEN OF THE CAMERA TO THE VEHICLE:

Again, connecting the viewing screen to a power source is based on the camera you intend to set up. Nevertheless, you’ll most probably get a display screen with a back view mirror and a quality transmitted at the back. The mirror will replace the conventional rearview mirror at the front of the windscreen. If you are using a wired system, you can link the cord of your camera to the cord from the screen at the rear of the vehicle. But in a wireless connection, the cord of the display screen can be laid through the dashboard and linked to a single power source, just like the one connected to the circuit.

STEP 7 — CHECK HOW THE CAMERA PERFORMS:

This is the last stage in the rear camera installation where you can start your car and test the rear camera to see how it performs. Ensure that the camera is not on at all times to increase its lifespan. Occasionally, you might discover that the reverse input is not communicating with the back signal. These are little fine-tuning you need to undertake. If all connections are now completed, you may proceed to use your rear camera anytime you’re reversing your car or when required.

This article has attempted to present to you steps you can take in installing a backup camera on your vehicle by yourself. I am fully persuaded if you follow these steps carefully, you’ll find the installation easy and get it correctly done. This tutorial is quite essential as having the best backup camera is central to a smooth and accident-free trip daily. We sincerely hope it helps.